This post contains affiliate links . Read full revealing statement here .
Use these free construction plan to created a improbable , raise bed unadulterated for plant containers . The stature make it soft to reach flower bay window and the design suit plastic bins for winter sowing . tote up wheel to make it moveable on a deck or patio .
Other free plans let in araised garden bottom with built - in privacy wallandseveral styles of raised garden beds .
Kreg Pocket Hole Jig
Make a Tall Raised Bed for Plant Containers
This planter is built like a tall raised garden bed but alternatively of occupy it with soil , it is used to domiciliate works containers . The plant shelf set aside for plenty of drainage so the unit can sit in the garden .
This has estimation forfilling the container with soilwithout pass a sight of money .
This next image shows a interbreeding - section with flower pot placed inside .
It is also the right size to fit plastic binful with or without lids . I use bins forseed startingincludingwinter sowing , and toharden offyoung plants ready for transplanting .
The height make the plants easy - to - entree without back strain .
By adding wheel , the entire unit can be moved around as call for on a patio or deck .
add up top rails for a finished facial expression .
Related : DIY Raised Garden Bed with Privacy Fence
Materials
This builds a box some 5 - feet ( 60 - inches ) long by 28 - column inch wide . The box is approximately 19 - inches deep . The unit is 3 - foot marvelous .
This lists factual versus nominal softwood dimensions .
- Do not cut these pieces until needed during assembly when you’re able to check exact size necessitate .
Tools
Assembly
This is the basic frame . There are four nook posts ( 4x4s ) and several 2x4s used to create the front , back , and side , and to support the plant shelf also made from fence dining table .
First check out that you have eight fencing boards that are all the same distance ( 60 - inch ) . The whole blueprint is based on the sizing of these boards . If some of your boards are a bit short , trim all 8 plug-in to the same length and use the young number as your take measure .
For a finished feel , the fence display board on the front and back sections will extend beyond the corner posts by just overone add-in widthat each destruction . This allows the side fencing boards to insert in nicely behind them work salutary - looking corners .
If , for case , your fence board are 5/8 - column inch thick like the 1 I used , the front and back fencing boards will extend beyond the posts a tomentum more than 5/8 - in at each goal .
In the diagram below , the foresighted 2x4s are shown as 52 1/4 ( 52.25)-inches long . In reality , there are always edition and imperfectness in lumber so we need to quantify exactly what your project needs .
To determine the right 2×4 length , take a fence board and place a niche post one board width ( e.g. 5/8 - inch plus a hair’s-breadth or two ) inside each end and strike out the inner boundary of each post . The distance between the two Post is the desire duration of your farseeing 2x4s .
Before forum , there is one more measuring needed .
Related : How to progress a Pond in a Raised Garden Bed
What are the existent widths of your fence add-in ? Mine are 5.25 - inch wide so four of them equals 21 - inch . This means the four fence boards on each side will run 21 - inches down from the top of the raised bed .
The lower border of the low-spirited 2x4s of the anatomy should be just unsure of 21 - inches from the top of the raised bed to be sure it wo n’t be visible when the fencing board are attached .
The 2x4s can be attached to the nook posts using aKreg Jig K4 Pocket Hole System . This allow for you to place prison guard in the end of the 2x4s right into the posts .
The 2x4s are much minute than the corner posts , so you require to ordinate them with the outer edges of the posts so the fencing boards will be wealthy with them .
retrieve to place the lower 2×4 just above the blank space where the bottom edge of your bottom fence panel will go . The diagram point 21 - inches but make it slenderly less .
The shorter 2x4s are used to join the front and back section . I thin out mine 20.25 - in long .
Again , use Kreg pocket holes to get together the 2x4s to the corner posts with 2.5 - inch deck of cards screws .
Be sure the low-down side 2x4s are line up with the front and back abject 2x4s .
The final frame piece is a 2×4 used to join the grim front and back 2x4s in the middle of the raised bed . This will supply special backup for the fence board ledge that holds the plants . Take a measurement to know the precise length want . It will be approximately 24 - inches long . you could either use pocket holes or drill through the exterior of the long 2x4s .
Front and Back
Mark screw locations with pencil on all eight fence boards . I used two 1.25 - inch screws at each board end . They should be two inches from each of the board ends and one - inch away from top or bottom edge . practise a pilot hole for each ass .
When attaching fence boards , start with the top boardso it is utterly line up with the top edges of the corner mail and upper 2x4s and remember to position each one with one - board width beetle at each death .
Side Fence Boards
Measure length require for side fence board . You want them to fit nicely between the front and back fencing boards . Mine were just under 27 - in long .
Attach Wheels
With the sides in place , now is a just time to attach the wheels if you are using them .
Plant Shelf Fence board
The remain three fencing boards will spring the industrial plant shelf inside the raise bed . Your fencing boards are 60 - inches long but will postulate to be cut down slightly to fit . Measure the actual size needed , cut the boards to size , and billet in spite of appearance . The gaps between them allow for drainage . you’re able to attach these board with screws but I ’ve found no need for this .
Related:14 Tall Raised Bed & Salad Table Ideas
To give the raised bed a ruined look , add track around the top to hide the superlative of the posts and 2×4 support .
These can be mitered or solid .
Decide if you want them to extend beyond the boundary or align with them .
I made mine extend beyond the front and back edges but line - up with the side .
This next ikon shows the mensuration I used . The front and back rail are 60 - column inch long . The side track are approximately 20.25 - inch .
If you require to paint , stain , or protect the Sir Henry Joseph Wood , it ’s sentence .
Then add your plants and enjoy .
Along with summer containers , I will be using mine forgrowing vegetables in the winter .
Related : Soil Calculator ( Mulch , Compost , & Potting Mix Too )
~Melissathe Empress of Dirt ♛
